Home > Error Codes > Gecko Spa Pack Troubleshooting

Gecko Spa Pack Troubleshooting

Contents

Spa Builders Spa Side Error Codes Sn1 = Nonfunctional high temperature sensor. System will restart when temp. Check for clogged filter. OH = High temperature condition, has reached 110ºF.

Please try the request again. Make sure that they are open.• Clean the filter(s), waterline skimmer and footwell suction for any blockage..• In extremely hot weather, check for proper cabinet ventilation.• Check for excessive filter duration. The low speed pump or circ. If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open https://spacare.com/spasideerrorcodes.aspx

Gecko Spa Pack Troubleshooting

Ecn: Spa operating in Economy Mode. Do not enter the water. Inspect these first:• Check slice or ball valves. FL = Flow.

Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional. Check for clogged filter FL2: Pressure switch problem. Refill, if necessary. Marquis Spa Error Codes Your cache administrator is webmaster.

System will restart when temp. Hot Tub Error Codes Hence the need for the BIG LIST of CODES. The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected.

Sensor plugged into jack B is not working. Balboa Spa Control Manual Expires 7/31/2015 TO ACTIVATE THE COUPON: Click the button below, a banner or Shop Now or  Buy-It-Now! button then pressing the mode or light button depending on the system. To Schedule Service Click Here: Contact Us Home | Service area | Contact Us | Testimonials | Blog Heater is shut down, but other spa functions run normally.

Hot Tub Error Codes

System will restart when temp. http://www.hottubworks.com/blog/spa-error-codes-the-big-list/ F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration Sundance Spa Side Error Codes ILOC : Interlock failure Gecko Spa Pack Troubleshooting Heater is shut down, but other spa functions run normally. Balboa Hot Tub Error Codes Balboa Control Manufacturer Scroll past Common Error Codes for: What common codes actually mean and what you can check prior to scheduling service Common Spa or Hot Tub Error

HFL = Substantial difference between temperature sensors detected. ILOC = Interlock failure - possible pump or ozone spike. (---) =Unknown water temperature. (Displays when first powered up after refill). dry: Inadequate flow in heater. (Displays on third occurrence of "dr" message) Pr: When spa is first actuated, it will go into Priming Mode ---: Unknown water temp. Generated Mon, 17 Oct 2016 04:54:56 GMT by s_wx1131 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection Vita Spa Error Codes

at heater.OHS = Overheat. Your cache administrator is webmaster. Pump may also be deactivated). The spa is at a temperature above 108° .

Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat. Gecko Hot Tub Troubleshooting YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. No action is necessary.

Generated Mon, 17 Oct 2016 04:55:04 GMT by s_wx1131 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

th3/39 = On startup indicates water temperature less than 39° F. Pressure switch not working SN: Non functional high temperature sensor. Your cache administrator is webmaster. Coleman Spa Error Codes SE: Spa operating in Standard-in-Economy Mode.

If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Status of the heater element is unknown. Sensor plugged into jack A is not working.Snb = Spa is shut down. The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater.

PSoL : Pressure switch open with low pump. SEoP = Sensor open or disconnected. Check for low water level and ensure pump is primed. In rare cases (usually warmer climates), the circulation pump may also cause overheating.

SE = Spa operating in Standard-in-Economy Mode. If display shows only this message (blinking) spa is shut down. Sitemap HOT TUB SUPPLY SUPERSTORE 1-800-770-0292 Sunday - Saturday7am - 7pm CST Customer Care | About Us | Contact Us | Track Your Order | Shopping Cart | Login HOME Your First Name: Your Email Address: HomeHot Tub HelpHot tub error codes Hot tub error codes Applied Computer Controls (ACC) CoLd : Temp in heater housing is below 40° F.

SEoP : Sensor open or disconnected.