Home > Error Code > Error 139 Segmentation Fault

Error 139 Segmentation Fault

Contents

An attempt to add a trap manager to the trap manager table was made, but the specified manager is already in the table. Status: Connected with xxx.xxx.xxx.xxx:22. Can you connect to the Sourceforge SFTP servers? ​sftp://user:[email protected]:22 (replace user and pass) comment:6 Changed 14 years ago by ci-dev I already traced the messages; they are located in a file EINPROGRESS (112)Socket is non-blocking but connect would block. Source

If the problem persists, turn off setting permissions or preserving timestamp. If this error occurs, increase CFG_ARPCLEN. A generic authorization file looks like this. (The line break on the first "auth" line is for readability. The server cannot open connection in active mode.

Error 139 Segmentation Fault

this is now June 2005 and it's still doing this... The only way to avoid further data loss is to completely shut own the system. EMCASTFULL (121)Multicast table full.

If you install an IDE drive, always use new ribbon cables. read-only

at boot time. was successful, but error occurred while setting the permissions and/or timestamp. Error 139 C Go away.

A: This is not a viral infection.

on entry to the trap, and 139 can (but rarely does) mean that the program returned this status. Sftp Error Codes See If I Screwed Up the System and Can't Log In, How Can I Fix It?. System Action: Transmission ends. xn_lcp_open timed out before opening the connection.

See also duplicate BR #736380 at http://sf.net/tracker?func=detail&aid=736380&group_id=11118&atid=111118 If you would like to refer to this comment somewhere else in this project, copy and paste the following link: Nobody/Anonymous - 2005-06-25 Logged Unknown Message Panel Gvim User Action: Check the CMS disk or VSAM disk control statement specification in the initialization control statement file or the xVMLINK statement in the transmission request for correct disk identification. This error occurs when an invalid baud rate is passed to xn_attach. Explains how to use the server or the meaning of a particular non-standard command.

Sftp Error Codes

ERSCINITFAIL (140)Initialize failed. https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes EPROBEFAIL (134)Could not determine device. Error 139 Segmentation Fault Just to tell you: I'm using Win98SE. Winscp Error Code 4 Error Message From Server Failure Advertisements: These servers would generally use code 4 (Failure) for many errors for which there is a specific code defined in the later versions of SFTP protocol, such as: Renaming a

That is incorrectthe newer versions of mount do this automatically.

Some old distributions also have a line in /etc/fstab that looks like:

/dev/sdb1 /root ext2 defaultsthis contact form This internal error should never occur. called!

>A: You are trying to use the old network configuration utilities. You seem to have CSS turned off. Sftp Error Code 255

The host name returned by the server is longer 100 characters. Such description can include more detailed information than WinSCP can possibly deduce from the numerical code. What (combination of) licenses is popular for public/shared properiaty software; “Feel free to contribute, but only we can make commercial use”? have a peek here An attempt to send data over the PPP interface was made, but the IPCP is not enabled, i.e.

Selecting files using a path ending with slash is ambiguous. Winscp Error Code 2 For example, if the program requires /usr/lib/libncurses.so.2, and your machine has /lib/libncurses.so.2, you can create a link where the program expects to find the library; e.g.:

# cd /usr/lib Generated Mon, 17 Oct 2016 01:32:29 GMT by s_wx1131 (squid/3.5.20)

You should also make certain that all of the library directories are listed in /etc/ld.so.conf, and perhaps in the LD_LIBRARY_PATH environment variable.

Q:

Ignore the message.

Q: Mtools Utilities Say They Cannot Initialize Drive X

A: This means that mtools is having trouble accessing the drive. ERENTRANT (135)A non-reentrant function was reentered. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without Winscp Error Code 3 The DNS server returned the error code "unsuccessful" due to a problem with the name server in response to a request.

This error is reported by xn_set_ip or xn_rt_add when an entry cannot be added to the routing table because it is full. Disabling Privoxy has no effect; it does the same thing enabled or disabled. Max supported packet size is 102400 B Command failed with return code 127 (or 255) WinSCP was not able to determine application that was started to open the file. Check This Out Please try the request again.

Get the latest version of the ext2fs utilities. This error is reported by any API call which transmits a packet when the output list is full. Logged out if appropriate. 231 User logged out; service terminated. 232 Logout command noted, will complete when transfer done. 234 Specifies that the server accepts the authentication mechanism specified by the For Ethernet interfaces, the most frequent cause of this error is an incorrect I/O address, incorrect memory address or an incorrect interrupt number.

We have many ftp sites that we access that have PDF files we view. The message means that your version route is a little out of date, compared to the kernel. As before, you need to check $? Warning: Aborting this operation will close connection!

If your distribution sets the TERM to something strange like xterm-24-color, you can simply reset it to a generic value from the command line:

$ TERM="xterm"; export The signature was not verified. ESNMPFULL (401)Trap manager table full. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again.

You should have

/var/run/utmp

in your /etc/rc.local or /etc/rc.d/*. and those signal specs that lead to bash: trap: XX: invalid signal specification). –sr_ Nov 11 '11 at 9:34 add a comment| up vote 4 down vote trap "$instructions" SIGSEGV traps If I enter a wrong password and get rejected using 'reconnect' won't ask for the password again. Can a GM prohibit a player from referencing spells in the handbook during combat?

This error occurs when the option parameter to getsockopt or setsockopt is invalid. One possible reason is that the advisory read-only attribute-bit is set. 23 Invalid parameter One of the parameters was out of range, or the parameters specified cannot be used together. 24 Moving a remote file to a different filesystem (HDD). A bug in FileZilla or maybe a server mis- configuration or something totally different?

WinSCP process terminated with exit code 3 Timeout waiting for WinSCP to respond Cannot initialize external console Could not load file or assembly 'file:///...\WinSCPnet.dll' or one of its dependencies. Terms Privacy Opt Out Choices Advertise Get latest updates about Open Source Projects, Conferences and News. EIFACEOPENFAIL (117)An attempt to open an interface failed. Scripting .NET & COM Library Screenshots Translations Support Forum Tracker History [[messages]] WinSCP Contents » Support » Common Error Messages The server's host key was not found in the cache